收藏本站
NXP Semiconductors
PCA9633
4-bit Fm+ I 2 C-bus LED driver
7.3.7 I 2 C-bus subaddress 1 to 3, SUBADRx
Table 14.
SUBADR1 to SUBADR3 - I 2 C-bus subaddress registers 0 to 3 (address 09h to
0Bh) bit description
Legend: * default value.
Address
Register
Bit
Symbol
Access Value
Description
09h
0Ah
0Bh
SUBADR1
SUBADR2
SUBADR3
7:1
0
7:1
0
7:1
0
A1[7:1]
A1[0]
A2[7:1]
A2[0]
A3[7:1]
A3[0]
R/W
R only
R/W
R only
R/W
R only
1110 001*
0*
1110 010*
0*
1110 100*
0*
I 2 C-bus subaddress 1
reserved
I 2 C-bus subaddress 2
reserved
I 2 C-bus subaddress 3
reserved
Subaddresses are programmable through the I 2 C-bus. Default power-up values are E2h,
E4h, E8h, and the device(s) will not acknowledge these addresses right after power-up
(the corresponding SUBx bit in MODE1 register is equal to 0).
Once subaddresses have been programmed to their right values, SUBx bits need to be
set to 1 in order to have the device acknowledging these addresses (MODE1 register).
Only the 7 MSBs representing the I 2 C-bus subaddress are valid. The LSB in SUBADRx
register is a read-only bit (0).
When SUBx is set to 1, the corresponding I 2 C-bus subaddress can be used during either
an I 2 C-bus read or write sequence.
7.3.8 LED All Call I 2 C-bus address, ALLCALLADR
Table 15.
ALLCALLADR - LED All Call I 2 C-bus address register (address 0Ch) bit
description
Legend: * default value.
Address
Register
Bit
Symbol
Access Value
Description
0Ch
ALLCALLADR
7:1
AC[7:1]
R/W
1110 000*
ALLCALL I 2 C-bus
address register
0
AC[0]
R only
0*
reserved
The LED All Call I 2 C-bus address allows all the PCA9633s in the bus to be programmed
at the same time (ALLCALL bit in register MODE1 must be equal to 1, power-up default
state). This address is programmable through the I 2 C-bus and can be used during either
an I 2 C-bus read or write sequence. The register address can be programmed as a
sub call.
Only the 7 MSBs representing the All Call I 2 C-bus address are valid. The LSB in
ALLCALLADR register is a Read-only bit (0).
If ALLCALL bit = 0, the device does not acknowledge the address programmed in register
ALLCALLADR.
PCA9633_5
? NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 05 — 25 July 2008
15 of 43
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
PCA9634D,118 IC LED DRIVER RGBA 20-SOIC
PCA9635PW/S911,118 IC LED DRIVER RGBA 28-TSSOP
PCA9685PW,118 IC LED DRIVER RGBA 28-TSSOP
PCA9922PW,118 IC LED DRIVER LINEAR 16-TSSOP
PCA9955TW,118 IC LED DRVR CONST CURR
PCF85102C-2P/03,11 IC EEPROM 2KBIT 100KHZ 8DIP
PCF85103C-2T/00,11 IC EEPROM 2KBIT 100KHZ 8SOIC
PCF8570T/F5,512 IC SRAM 2KBIT 100KHZ 8SOIC
相关代理商/技术参数
PCA9633BS-T 功能描述:LED照明驱动器 4BIT I2C FM+ TP LED CON RST OE RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633D16 功能描述:LED照明驱动器 LED DRVR 4BIT I2C RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633D16,112 功能描述:LED照明驱动器 LED DRVR 4BIT I2C RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633D16,118 功能描述:LED照明驱动器 4BIT I2C FM+ TP LED CON RST OE RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633DEMO 功能描述:开发板和工具包 - 8051 Brd Philips PCA9633 RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压:
PCA9633DP1,118 功能描述:LED照明驱动器 LED DRVR 4BIT I2C RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633DP1,118-CUT TAPE 制造商:NXP 功能描述:PCA9633 Series 25 mA 5.5 V 1 MHz SMT 8-bit I2C-Bus LED Driver - TSSOP-8
PCA9633DP2,118 功能描述:LED照明驱动器 4BIT I2C FM+ TP LED CON RST OE RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N